Xigmatek Hero II Air 4 Fan ARGB Mid Tower Case With Valkyrie 750W ATX 3.1 80 Plus Bronze Power Supply Combo

✅ Authorized Xigmatek Partner in Egypt | Official Case: 1 Year / PSU: 3 Years | Expert PC Building Consultation Available

⚡ Engineering Highlights at a Glance:

• 4 Pre-installed ARGB Fans: Three front intake fans and one rear exhaust fan come pre-installed, with an LED switch on the top I/O for quick lighting changes.
• Front Mesh Airflow Design: The mesh front grille allows unrestricted air intake, which suits high-TDP CPUs and GPUs under sustained load.
• Valkyrie 750W ATX 3.1 PSU: 80 Plus Bronze certified with a 62.5A +12V rail (750W total) and a 12V-2×6 cable for current-generation graphics cards.
• 360mm Front Radiator Support: Fits 120mm, 240mm, or 360mm AIO liquid coolers at the front, plus a 120mm radiator at the rear.
• 340mm GPU Clearance: Accommodates most high-end graphics cards, with 165mm of CPU cooler height clearance for large tower air coolers.
• Storage Flexibility: Two 2.5-inch SSD mounts on the motherboard panel plus two 2.5-inch/3.5-inch combo bays in the HDD cage.
• Tempered Glass Side Panel: Shows off the ARGB fans and internal components for a clean showcase build.

Case Clearance and Component Fit

The Hero II Air supports ATX, Micro-ATX, and Mini-ITX motherboards. Confirm your GPU length does not exceed 340mm, and your CPU cooler height does not exceed 165mm. The case measures approximately 195 x 448 x 388mm (W x H x D) and weighs around 4.47kg empty. Check your desk or floor space before ordering, especially if you plan to use a large air cooler or a long graphics card.

Valkyrie 750W PSU Considerations

The bundled Valkyrie 750W PSU is ATX 3.1 and PCIe 5.1 compliant, with a dedicated 12V-2×6 cable for modern NVIDIA and AMD GPUs. The +12V rail delivers up to 62.5A (750W), which is enough for most single-GPU gaming builds. Note that the PSU input is rated for 220V–240V, 8A, 50–60Hz, which matches Egyptian mains voltage. Check the specific GPU power connector requirements before building; if your card needs more than one 12V-2×6 cable, verify the PSU’s included cable set.

Cooling and Fan Configuration

The case ships with three front 120mm ARGB fans and one rear 120mm ARGB fan, controlled via the top I/O LED switch. For additional cooling, the top supports two 120mm or two 140mm fans, and the front supports a 360mm radiator. If you install a top-mounted AIO, check that the radiator thickness and fan clearance do not interfere with tall VRM heatsinks or RAM. The front mesh design favors airflow over noise isolation, so if you want a quieter build, consider a fan curve that keeps the front fans below full speed under light loads.

Plan your build around the case’s clearances: GPUs up to 340mm, CPU air coolers up to 165mm, and ATX motherboards. The four pre-installed ARGB fans and front mesh handle airflow for most mid-range to high-end builds without adding extra fans.

The Valkyrie 750W PSU includes a 12V-2×6 cable for modern GPUs. Check your graphics card’s power connector before building; if it needs a 12V-2×6 connection, this PSU covers it. If it needs multiple 8-pin cables, verify the included cable set matches your GPU’s requirements.

Use the top I/O LED switch to cycle through ARGB lighting effects without opening software. For more control, check whether your motherboard has a 5V ARGB header and whether the case’s fan controller can sync with it; if not, the onboard LED switch handles basic effects.

If you plan to add a front-mounted 360mm AIO later, confirm the radiator thickness fits within the front clearance. The case’s mesh front favors airflow over noise isolation, so set a fan curve that balances cooling and acoustics for your workload. The 1-year case and 3-year PSU warranty cover manufacturing defects.